Counselling Code

Mechanical Engineering - Publication

  • Best Student Project-2017 from Dr. Kalam Educational Trust - S.

  • Dr.T.Prakash, Professor received Innovative Technological Research Award - 2018

  • Mr.G.Tharanitharan AP/Mech  Received Best Teacher Award - 2018

  • Secured 4th place &  Best Innovation Award - Go-kart Event  2017-18

  • Best Outstanding Award - Mr.K.Gowtham, (Batch 2014-2018)

  • ISTE Best Student Award 2017 – Mr.A.Aravindraj (Batch 2014-2018)

  • The Department of Automobile Engineering and the Department of Mechanical Engineering organizing

  • Vijay Aravind.R, University Rank - 30

  • Branch Toppers

  • Best Outstanding Award - K.Ranjithkumar(2013-17)

  • ISTE Best Student Award 2016 - T.Tharoon

  • Metrology lab

  • PG Thermal Lab - VCR Engine

  • CAM Laboratory

  • Twenty Students of Mechanical Engineering have participated in GOKART Event organized by Imperial

Latest News Feed

Publication

Faculty Publications

2008-2009

 

  1. P.Tamilselvam ,PSS.Srinivasan, E.Vallinayagam, published a paper on “A simple prediction method for laminar Film condensation over horizontal integral - fin copper tubes “, Journal of energy, heat and mass transfer.  Volume 30  pp 311-322, 2008.

 

2009-2010

 

  1. K. Senthilkumar. PSS Srinivasan, published a paper on “Optimizing Process Parameters of Centrifugal Evaporative Air Cooler”, International Journal of Recent Trends in Engineering and Technology, Volume 3 No .6. 2010.
  2. K.Senthilkumar, ., & P. S. S  Srinivasan,. published a paper on  “Application of Taguchi method for the optimization of system parameters of centrifugal evaporative air cooler” ,Journal of Thermal Science, volume19  ,issue 5, PP 473-479.2010.
  3. M.Manjuladevi ,D.Jalajaa , S.V.Saravanan ,  published a paper on “Removal of pb(II) from aqueous solution by activated carbon prepared from artemesia vulgaris - stem waste”, Enviromediavolume 28, issue 1,PP 313-318,2009.
  4. M.Manjuladevi ,D.Jalajaa , S.V.Saravanan, published a paper on “Removal of acid dye from textile waste water by absorption using activated carbon prepared from punicagranatum (Pomagranate) rind” ,Enviromedia , volume 28, issue 1:313 318,2009.
  5. S.V.Saravanan , K.Krishnakumar , S.Bhuvanesh , Kiran.H.Nair published a paper on “Technology scan  to access the state of art of knowhow of  Nano fuel saver of  IC engines for emission reduction” , International journals of pollution research, volume 28, issue 1223-226,2009.

 

2010-2011

 

  1. K.Thirumalaikannan , B.Senthilkumar, published a paper on “Heat transfer and fluid flow analysis in plate fin and tube heat exchangers with different shaped vortex generators” ,soft computing and engineering,volume-2,2231-2307,2011.
  2. K Senthilkumar,.,& P. S. S Srinivasan,. published a paper on “Experimental study of centrifugal humidifier fitted in an industrial shed located in tropical climates”, Thermal Science, volume 15, issue 2, 467-475.2011.

 

2011-2012

 

  1. K Senthilkumar,.,& P. S SSrinivasan,.. published a paper on “A Parametric and Experimental Study of a Centrifugal Atomizer Fitted in an Industrial Shed Located in a Tropical Climate”. Arabian Journal for Science and Engineering, volume 37, issue 4, pp 1089-1100,2012.
  2. L.Savadamuthu ,S.Gunashekharan. published a paper on “Study on equipment failure and loss estimation through Taguchi method with risk management” International Journal of engineering and advanced technology , Volume 1, Issue 3,2012.
  3. R Kumaravelan,.,P.Srinivasan,          P Tamilselvam,., & M Madhan,. published a paper on “Intensification of the Subsisting Methodology to Enhance DFM without Discretization” The Arabian Journal for science and engineering  , Manuscript no AJSE-D-11-01016,.2011.
  4. L.Savadamuthu ,P.Vivekanandan. . published a paper on “Optimization of cutting parameters for turning process using genetic algorithm”. European Journal of Scientific research, Volume  69, Issue  .1 , pp73-80 ,2012.
  5. L.Savadamuthu ,K.Thirumalaikannan. published a paper on “Optimization of operating parameters in wire electrical discharge machining for improving quality using genetic algorithm”, International journal of engineering and advanced technology   International, Volume 4, issue 1, 2012.
  6. L Savadamuthu,., S Muthu,., &          P Vivekanandan,. published a paper on “Quality Improvement in Turning Process using Taguchi's Loss Function”. International Journal of Soft Computing and Engineering, volume 1, issue 4 .pp 2231-2307.2011.

 

 

2012-2013

 

  1. S.Nareshkumar, S.Gunashekharan,, published a paper on “Design and analysis of dynamic vibration absorber (DVA) to reduce vibration in rails”, Internal journal of engineering and applied science,Volume-3,pp 2305-8269 , 2013.
  2. R Kumaravelan,., P Srinivasan,., P Tamilselvam,., & M.  Madhan, published a paper on “Intensification of the Subsisting Methodology to Enhance DFM without Discretization”. Journal of Engineering and Technology, Volume 2, Issue 2, pp 87-96, 2013.
  3. P.Vivekanandan, M.Kumar, published a paper on “Modelling, Design and finite element analysis of camshaft” , International journal of current engineering and  technology, volume 3, issue 10, pp 2277-4106,2013.
  4. P.Vivekanandan , V.P.ArunachalamT.Prakash, L.Savadamuthu, published a paper on “The experimental analysis of friction stir welding on Aluminum composites” , Internal journal of metallurgical engineering, volume 1, issue 4,pp 60-65 , 2012.
  5. P.Vivekanandan ,V.P.Arunachalam published a paper on, “The experimental analysis of stir casting method on Aluminum-fly ash composites”, International journal of current engineering and  technology, Volume 3 issue 1,2277-4106 , 2013.
  6. R Thirumalai,.,&J.S.Senthilkumaar,.  published a paper on “Multi-criteria decision making in the selection of machining parameter  in machining Inconel 718”. Journal of mechanical science and technology”, volume 27, issue 4,1109-1116. 2012.
  7. R Thirumalai,., J. S Senthilkumaar,., P Selvarani,., & S Ramesh,. published a paper on “Machining characteristics of Inconel 718 under several cutting conditions based on Taguchi method. Proceedings of the Institution of Mechanical Engineers”, Part C: Journal of Mechanical Engineering Science, Volume 01 , Issue 9  .2012.
  8. R.Thirumalai,  J  S.Senthilkumar, P.Selvarani,, RM. Arunachalam,     KM. Senthilkumar, published a paper on “Investigation of surface roughness and flank wear behavior  machining of  Inconel 718”,Institution of engineers Australia, volume 10, issue 2, 2012.

 

 

 

 

2013-2014

 

  1. M., Sureshkumar, P Tamilselvam,., R Kumaravelan,., & R Dharmalingam,. published a paper on Design, “Fabrication, and Analysis of a Hybrid FIBER Composite Mono leaf Spring Using Carbon and E-Glass Fibers for Automotive Suspension Applications”. Mechanics of Composite Materials, Volume 50, Issue1, pp 115-122. 2014.
  2. R Kumaravelan, P Tamilselvam,    VC Gandhi, S Ramesh , published a paper on “Analysis of contact  parameters in the sphere and flat contact model by flattening approach”, OXIDATION COMMUNICATIONS , Volume 36 ,issue 4, pp1202 - 1216 , 2013.
  3. B Parthasarathi , K Nagaraj , Sridhar. S ,Karthik,  R Dharamalingam, published a paper on “CFD analysis of integrated catalytic converter and muffler for automobile exhaust system”, Journal of current developments in mechanical engineering”, Volume 1 Issue 1 . 2013.
  4. L Savadamuthu,., S Muthu,., T.Rakhul, & S Jothimani,. published a paper on “Multi Characteristic Optimization in Wire Cut EDM by Using Taguchi Data Envelopment Analysis Based Ranking Methodology”. International Review of Mechanical Engineering, Volume 7 Issue 3.  2013.

 

2014-2015

 

  1. K Jeyaprakash,., M. M Ariffuddeen,., J Selvakumar,., & V Karthik,. published a paper on “Prediction of Flow Coefficient and Hydrodynamic Torque Coefficient in Butterfly Valve”. Middle-East Journal of Scientific Research, Volume 22 issue 7,  pp 1077-1081.2014.
  2. R.Dharamalingam ,Dr.K.SivagnanaPrabhu , B.Senthil Kumar , R.Thirumalai, published a paper on “Nano materials and  Nano fluids : an innovative technology study for new paradigms for technology enhancement” Procedia engineering, Volume 97,  pp 1434-1441,2014.
  3. S.Jayachandren, K.Vijayakumar ,R.Dinek, published a paper on ERP “Implemented in fab tech  industry using S A P”, Internal journal of innovative research in science , engineering and technology, Volume 3 issue 11,2319-8753, 2014.
  4. T Prakash,., S Sivasankaran,., &        P Sasikumar,. published a paper on “Mechanical and TribologicalBehaviour of Friction-Stir-Processed Al 6061 Aluminium Sheet Metal Reinforced with Al2O3 / 0.5 Gr Hybrid Surface Nanocomposite”. Arabian Journal for Science and Engineering, Volume1-11.2014.
  5. K. S Kumar,., J. S Senthilkumaar,., & R Thirumalai,. published a paper on “Chip Morphology Investigation among Dry, Wet and Gas Cooled Machining of Super Duplex Stainless Steel” Applied Mechanics and Materials Volume. 592-594, pp. 811-815,2014.
  6. R Thirumalai,., S Srinivas,.,T Vinodh,., A. L Kowshik Kumar,., & M. K Kumar,. . published a paper on “Optimization of Surface Roughness and Flank Wear in Turning SCM440 Alloy Steel Using Taguchi Method” Applied Mechanics and Materials  ,Volume. 592-594, pp. 641-646 , 2014.
  7. Shiva Sharma , M.ChandrasekaranR.Thirumalai , published a paper on “Application of  Taguchi desirability function analysis (TDFA) for optimizing responses in turning  inconel 718”,Applied mechanics and materials, Volume 13 Issue 6 ,2014.
  8. Shiv Sharma, M Chandrasekaran,.,& R Thirumalai,. published a paper on “Multi-Objective Optimization of Surface Roughness and Tool Wear in Turning Inconel 718: A Desirability Analysis, Genetic Algorithm and Firefly Algorithm”. Applied Mechanics and Materials Volume. 592-594, pp. 545-549 ,2014.
  9. S Gunasekharan,.,D.Elangovan ., &  P Parthiban published a paper on “Comprehensive Study to Evaluate the Critical Success Factors Affecting Lean Concept in Indian Manufacturing Industries”Applied Mechanics and Materials, Volume. 592-594, pp. 2569-2576, 2014.
  10. S Gunasekharan,.,D.Elangovan ., &  P Parthiban, published a paper on.“Critical Success Factors for Implementation of Lean and Green in Medium Scale Manufacturing Industries” ,Applied Mechanics and Materials , Volume. 592-594, pp. 2588-2595, 2014.
  11. T.Prakash , P.SasikumarS.Sivasankaran , published a paper on “Investigations on the microstructure and mechanical property of friction stir process AA6061 Aluminum sheet metal reinforced with Al2O3 surface composites” , International journal of materials engineering innovation, Volume 5 ,  Issue 3, pp.192-204,2014.
  12. K.Vijaykumar,Jayachandran,  Dinek.R, published a paper on ERP Implemented  in Fabtech Industry Using SAP, Vol.3,      Issue 11
  13. R.Dharmalingam, C.Chinnusamy, B.Senthil kumar, published a paper on Optimization Studies on the performance characteristics of solar flat-plate collector using Taguchi method
  14. C.Chinnusamy published a paper on ,Experimental Investigations on the effect of compression ratio on SI engines using fuel additives,ISSN 0973-4562,Vol.10,No.19(2015)
  15. K. Jeyaprakash,A.VimalKodeeswaran, P. Yuvaraj, published a paper on A Survey on Machine Scheduling Techniques,ARPN Journal of Engineering and Applied Sciences, P. No. 1966-1969 VOL. 10, NO. 4, MARCH 2015 ISSN 1819-6608
  16. A.Chelliah, B.Karthick, A.VimalKodeeswaran,V.R.Hariram, published a paper on Helmet cooling system using phase change material for Long drive,ARPN Journal of Engineering and Applied Sciences ,ISSN 1819-6608,Asian Research Publishing Network (ARPN).
  17. Dr.P.Tamilselvam, published a paper on Analysis of Boiler Tube Failure in 210MW At Mettur Thermal Power Station,issn 0973-4562 Vol.10,No.9(2015)
  18. C.Chinnusamy published a paper on ,Experimental Studies on Optimization of VCR Diesel Engine parameters using Taguchi Method,ISBN:978-93-80686-98-1,Serial no.85653200
  19. G.Tharanitharan,R.Madhan,   V.Vinoth, published a paper on Investigation on Property Relationship in Various Austenitic Stainless Steel 304L Weld,Vol.5,Issue 3,March 2015.

 

2015-2016

 

  1. J.Selvakumar, K.Natarajan, published a paper on “ Failure Analysis of Centrifugal Pumps based on Survey “,APRNJournal of Engineering and applied Sciences.  Volume 10  pp1960-1965, March 2015.
  2. C.Senthil Kumar, A,S,Krishnan, Daniel Dickson Jeyakumar, P.Tamilselvam, published a paper on A. Brusly solomon, “ Effectiveness Analysis of a Thermosyphon Charged with Refrigerant R-134a as a Working Fluid“,International Journal of Applied Engineering Research.  Volume 10 (No.57) pp262-266, March 2015.
  3. S.Muthumanickam, C.Chinnasamy,A.Mohan,
    S.Karthik, published a paper on “ Experimental Studies on Optimisation of VCR Diesel Engine parameters using Taguchi Method“,International Journal of Applied Engineering Research.  Volume 10 (No. 39)  pp29621-29626 , 2015.
  4. Gunasekharan.S, Elangovan.D, Hariram.V.R, published a paper on “ Strategic Approach towards Lean Industrial Transformation from Traditional Systems using Lean Industrial Model for Sustainability (LIMS)“,International Journal of Mechanical Enginnering and Information Technology.Volume 3  pp 1494 -1501 2015.
  5. S.Ramkumar,C.Chinnasamy, J.Yogaraja, B.Karthik,
    published a paper on  “ Performance and Emission Characteristic Studies of Diesel Engine Fuelled with NeemOil“,International Journal of Mechanical Engineering and Research.  Volume 5 (No.01) pp77-83, 2015.
  6. M.Sureshkumar, P.Tamilselvam, G.Tharanitharan, published a paper on “Experimental Investigation of Hybrid Fiber Mono Composite Leaf Spring for Automobile Applications“,International Journal of Mechanical Engineering and Research.  Volume 5 (No.01) pp 89-93, 2015.
  7. R.Dharmalingam, K.K.Sivagnanaprabhu, J.Yogaraja, S.Gunasekharan, R.Mohan
    published a paper on “Experimental Investigation of Heat Transfer Characteristics of Nano Fluid Using Parallel Flow, Counter Flow and Shell and Tube Heat Exchanger “,International Journal of Archive of Mechanical Engineering.Volume 62 pp 509-522, 2015.
  8. R Dharmalingam ,K K Sivagnanaprabhu, B Senthil Kumar, S Periyasamy 
    published a paper on “ Experimental Investigation and Mathematical Study of Performance Characteristics of Solar Flat Plate Collector Using Al2O3 /Water Nano Fluid “,International Journal of Mechanical Engineering and Research.  Volume 5 (No.01) pp84-88, 2015.
  9. Karthik.V, Hariram V.R, Karthick.B, Sindhukavi.M
    published a paper on  “Flexible Manufacturing System layout Optimization (Using Heuristic Technique)" International Journal of Applied Science and Research.
    pp 204-215,December 2015
  10. Karthick.B, Sindhukavi.M,Karthik.V, Hariram V.R published a paper on “Effect of Heat input on Mechanical and Microstructure Properties of 316L Stainless Steel Plates “, International Journal of Applied Science and Research. pp 216-220,December 2015.
  11. K Prakash published a paper on “Efficiency Improvement in Shell and Tube Heat Exchanger Using CFD Tool“, International Journal in Science, Engineering and Technology  Vol 5 Issue no 3 March 2016.
  12. Tharanitharn G, Tamil Selvam P, Kumaravelan R, SureshKumar M, Vinoth V
    published a paper on “Study on Mechanical Properties of Hybrid Woven Fibre Reinforced Polymer Composite“, International Journal of Applied Engineering Research.
    pp 397- 405, Vol. 10 No. 50 (2015)
  13. Vijay Aravind R Tharanitharn G Sriraman M published a paper on “Quick Lifting Jack with bevel Gear Arrangement “, International Journal of Applied Engineering Research.
    pp 397- 405, Vol. 10 No. 85 (2015).
  14. R.Thirumalai  Karthik S published a paper on “Friction Stir Welding Aa1100 Aluminium Alloy “, International Journal of Advances in Natural and Applied Sciences.
    Pp57-66, Vol. 10 No. 6 (2015).
  15. T Venkatajalapathi, A S Krishnan, published a paper on “Experimental Investigation on Use of Liquid Alcohol Mixture for Cooling of Electronic Equipment in a Square Enclosure“, International Journal of Advances in Natural and Applied Sciences. pp 244-250, Vol. 10 No. 6 (2016)
  16. T Prakash  P Sasikumar ,S Sivasankaran , published a paper on “The Influences of the Friction Stir Processing on the Microstructure and hardness of Al7075 Aluminium sheet Metal Reinforced with SiC/3% B4C Hybrid Surface Nano Composite“, International Journal of Advances in Natural and Applied Sciences. pp 21-25, Vol. 10 No. 6 (2016)

 

 

 

2016-17

  1. L.Savadamuthu,K.Malarvizhi and T.Rakhul , published a paper on"  Study on Machinining Parameters of AISi H 13 Diesteel in Wire-Dem Process " , Asian Journal of Research in Social Sciences and Humanities, ISSN: 2249-7315, Vol..6 , No. 6, pp 499-507,June 2016.
  2. K.Malarvizhi , L.Savadamuthu , and MadhusudhanKumar,   published a paper on            " ELM Based Speaker Dependent Speech to Text Conversion" , Asian Journal of Research in Social Sciences and Humanities, ISSN: 2249-7315, Vol..6 , No. 6, pp 811-823,June 2016.
  3. T.Prakash  P.Sasikumar, S.Sivasankaran, published a paper on "Experimental Inhvestigation of Friction Stir Processed Al7075 Aluminium Plate Reinforced with AL2O3 / 1%  Gr Hybrid Surface Nanocomposite", Asian Journal of Research in Social Sciences and Humanities, ISSN:2249-7315, Vol.6, No. 7, pp 892-901, July 2016.
  4. C.Somu, published a paper on Analysis of Mechnaical Characteristics of Aluminium Nano Composites using MWCNT, International research journal of Engineering  and Technology, ISSN:2395-0056, Vol no.3 Issue 10, pp 236-240  Oct 2016.
  5. S.Hemnath,  P.Janagarathinam, M.Senthilnathan, published a paper on "Design of Automatic car mat cleaning machine", IJournal of engineering Research and Technology,ISSN:2278-0181, VOL.5, Issue 10, pp 311-317, oct 2016.
  6. V.Sathiyamoorty,T.Sekar and M.Subramanian , published a paper on "  Experimental investigation on the effects of nano fluid in ECM of high carbon high chromium die tool steel" , Asian Journal of Research in social sciences and humanities,ISSN: 2249-7315, vol.6, issue 8
  7. S.Hemnath,  P.Janagarathinam, M.Senthilnathan, published a paper on"Design of Automatic car mat cleaning machine", IJournal of engineering Research and Technology,ISSN:2278-0181, VOL.5, Issue 10, pp 311-317, oct 2016.
  8. R.Ganeshkumar, L.Venkatesh, A.Umashankar published a paper on" Analysing Heat transfer In annular stepped fin" , IJournal of engineering Research and Technology,ISSN: 2278-0181, Vol.5 , Issue 10, pp 144-152, oct 2016.
  9. P.Janagarathinam, Tharoon.T and Senthilkumar.K, published a paper on"The Assessment of Delamination in the drilling od EN8 steel by using Taguchi Method", IJournal of engineering Research and Technology,ISSN:2278-0181, VOL.5, Issue 09, pp 644-648, sep 2016
  10. A. Brusly Solomon,  A. M. Ram Kumar, K. Ramachandran, B. C. Pillai, C. Senthil Kumar,  Mohsen Sharifpur  and Josua P. Meyer , published a paper on"Charecterisation of a Heat Pipe with an Anodised Surface", IJournal of Heat and Mass Transfer,Springer,ISSN  Print 0947-7411, online 1432-1181, pp 1-11  , June 2016.
  11. A Natarajan, K.Kombiah, M.Krishnamoorthi, published a paper on"PLC Based Solar Panel With Tilting Arrangement", International Research Journal of Engineering and Technology, ISSN:2395-0072, Vol.3, No. 4, pp 2404-2411, April 2016.
  12. M.Mohamed Ariffuddeen , published a paper on" Performance Analysis on Disc Brake of Super Bikes", International Journal Engineering Research and Technology, ISSN: 2278 - 0181  Vol.5 , Issue no. 10, pp 422-430, October 2016.
  13. P.Vivekanandhan, T.Prakash, published a paper on" Evaluations of Tribological Properties and Optimization of Wear and Fricition of Aluminium Alloy 7075 Hybrid MMC Reinforced with Flyash, SiC and WC Using ANOVA and Genetic Algorithm", International Journal of Printing, Packaging & Allied Science, ISSN: 2320-4387  Vol.4 ,No. 5, pp 4013-4027, December 2016.
  14. T.Prakash, P.Vivekanandhan P.Sasikumar , published a paper on" Prediction of Effect of Reinforcement Volume Fraction on Mechanical and tribological Properties of Stir Casted AA2014/SiC MMC's", International Journal of Printing, Packaging & Allied Science, ISSN: 2320-4387  Vol.4 ,No. 5, pp 4028-4036, December 2016.
  15. K.Prakash published a paper on"Optimisation of Wind Turbine with Diffuser using CFD Tool" International Journal of Engineering Sciences & Research Technology, ISSN:2277-9655 Vol no. 6 Issue no 1, Jan 2017
  16. C Somu, A.Karthi, Sanjay Singh, R.Karthikeyan, published a paper on " Synthesis of Various Forms of Carbon Nanotubes by Arc Discharge methods - Comprehensive Review", International Research Journal of Engineering and Technology, ISSN: 2395-0056 Vol.4 ,No. 1, pp 344-354, Jan 2017
  17. G.Tharanitharan,  P Tamil Selvam published a paper on"Design and Fabrication of rotatary Tiller Blade", International Research Journal of Engineering and Technology, ISSN: 2395-0072 Vol.4 ,No. 1, pp 1007-1012, Jan 2017
  18. R Dharmalingam, R.Kandasamy, K.K.Sivagnana Prabhu , published a paper on " Lorentz Forces and Nanoparticle Shape on Water based Cu, Al2O3 and SWCNTs",  International Journal of Molecular Liquids,  ISSN: 0167-7322  Vol.1, pp 01-10, Februaury 2017
  19. Ganeshkumar R published a paper on"Design, Fabrication and Comparision of Heat Transfer analysis in Annular Disc Fin and  Annular Stepped Fins by Experimental and Numerical Methods " International Journal of Engineering Sciences & Research Technology, ISSN:2278-0181 Vol no. 5 Issue no 7, pp 1- 9 March 2017
  20. Chelliah A published a paper on"Diminishing the casting defects by using optimization technique " International Journal of Engineering Sciences & Research Technology, ISSN:2278-0181 Vol no. 5 Issue no 7, pp 136- 140 March 2017
  21. Karthik V published a paper on"Extraction of biodiesel from jatropha oil by Transesterification process " International Journal of Engineering Sciences & Research Technology, ISSN:2278-0181 Vol no. 5 Issue no 7, pp 163- 166 March 2017
  22. Karthik V published a paper on"Design and simualtion of truck cabin cooling system by Vapour absorption Refrigeration system using Engine Exhaust" International Journal of Engineering Sciences & Research Technology, ISSN:2278-0181 Vol no. 5 Issue no 7, pp 115- 118 March 2017
  23. G Tharanitharan "published a paper on Analysis of Mechanical Properties of Hybrid Cocous Nuicifera & Agva Sisalana Woven Fiber Laminate Composities" International Journal of Engineering Sciences & Research Technology, ISSN:2278-0181 Vol no. 5 Issue no 7, pp 32- 35 March 2017


 

 

2017-18

  1. M.Subramanian, P.Janagarathinam, T. Prakash, V.S.Kaushik ,"Optimization of Process Parameters for CN Turning of Al7075-T6 using RSM and GA to minimize the vibration amplitude" Journal of Advances in natural and applied sciences, ISSN: 1995-0772 Vol.4 , Issue No. 1, pp 250-259, Apr 2017.
  2. P.Janagarathinam, "A Study On Wet And Near-Dry Electrical Discharge Machining Process Of Inconel 718" Journal of Advances in natural and applied sciences, ISSN: 1995-0772 Vol.4 , Issue No. 1, pp 260-269, Apr 2017
  3. Jithin Velayudhan, "Design and Analysis of  Fixture for a Bearing Plate", International Research Journal of Engineering and Technology, ISSN: 2395-0072 Vol.4 , Issue No. 4, pp 1-5, Apr 2017
  4. Chinnasamy C, Tamilselvam P, V.Karthik, B.Karthick "Optimization and characterization studies on Green synthesis of Silver Nanoparticles using Response Surface Methodology" Journal of Advances in natural and applied sciences, ISSN: 1995-0772 Vol.4 , Issue No. 1, pp 214-221, Apr 2017
  5. S.Hemnath,  A.Natarajan, A.Karthi ,  K.Prakash, "Design And Development Of Tig Welding Test Rig "  Journal of Advances in natural and applied sciences, ISSN: 1995-0772 Vol.4 , Issue No. 1, pp 270-276, Apr 2017
  6. T.Pravin, "Investigation on Mechanical Properties of Aluminum with Copper and Silicon Carbide Using Powder Metallurgy Technique" Journal of Advances in natural and applied sciences, ISSN: 1995-0772 Vol.4 , Issue No. 1, pp 277-280, Apr 2017
  7. M.Sureshkumar,  P.Tamilselvam, G.Tharanitharan, "Analysis Of Hybrid Fiber Mono Composite Leaf Spring For Automobiles"Journal of Advances in natural and applied sciences, ISSN: 1995-0772 Vol.4 , Issue No. 1, pp 281-287, Apr 2017
  8. Hariram V R, Karthick B, "Improving Industrial Performance Using Lean Tools And Operations Research"Journal of Advances in natural and applied sciences, ISSN: 1995-0772 Vol.4 , Issue No. 1, pp 295-299, Apr 2017
  9. Sanjay Singh, Somu C, Arumugam, "Property correlations of cast AA 713.0/MWCNT metal matrix composite" Journal of Advances in natural and applied sciences, ISSN: 1995-0772 Vol.4 , Issue No. 1, pp 222-234, Apr 2017
  10. Mohammed Ariffudeen, "Fatigue analysis of Stiffness panel with a large cut out in an aircraft", International Journal of  Scientific Research Organisation, ISSN: 2456-694, Vol no. 1, Issue no. 2 May 2017
  11. Mohammed Ariffudeen, "Design and Analysis of Chevron nozzle in Aerodynamic", International Journal of  Scientific Research Organisation, Vol no. 1, Issue no. 2  ISSN: 2456-6942, May 2017
  12. R.Ranjith, "Predicting the Tensile Strength of Friction Stir Welded Dissimilar Aluminum Alloy using ANN", International Journal of Civil Engineering and Technology Vol no8, Issue no. 9 ISSN: 0976-6308, Sept 2017
  13. R.Ranjith, "Influence of Titanium - coated (B4Cp+SiCp) particles on sulphide stress corrosion and wear behaviour of AA7050 hybrid composites (for MLG Link)"   Journal of Australian Cermaic Society,  Aug-17
  14. Senthil Kumar C "Experimental Studies on Heat Transfer Characteristics of SS304 Screen Mech Wick Heat Pipe", Society of Thermal Engineers of Serbia, Vol 21, Suppl. 2, pp S497 - S50, Dec 2017
  15. G.Tharanitharan “Modeling On Machinability Parameters Of Hybrid Coir/Sisal Reinforced Vinyester Composite –Taguchiapproach” TAGA JOURNAL VOL. 14, Feb 18
  16. Kaushik V S “Optimization of End milling tool Geometry Process parameter for minimizing Surface Roughness Of AL 7068 Based on Response Surface Methodology” TAGA JOURNAL VOL. 14, Feb 18
  17. Naveenkumar.M and Pravin. T, “2.2l engine 1d simulation & experimental analysis of exhaust manifold”, International Journal Of Innovative Research Explorer, Volume 5 - Issue 3 - March 2018
  18. Chinnasamy C and Dr.Prakash. T, “Review on influence of corrosion and cavitation on various materials of diesel engine parts while using biodiesel as fuel”, International Journal Of Innovative Research Explorer, Volume 5 - Issue 3 - March 2018
  19. Dr. Prakash. T, “Performance analysis on oxygen enriched diesel engine for various compression ratios ”, International Journal Of Innovative Research Explorer, Volume 5 - Issue 3 - March 2018
  20. Janagarathinam P and Dr.Subramanian.M, “A literature survey on mechanical properties in aluminum matrix reinforced composites”, International Journal Of Innovative Research Explorer, Volume 5 - Issue 3 - March 2018
  21. Dr.Subramanian.M, “Design and fabrication of automatic corrugated partition box assembler”, International Journal Of Innovative Research Explorer, Volume 5 - Issue 3 - March 2018
  22. Dr.L.Savadamuthu, M.Saravanakumar and M.Sureshkumar, “Multi characteristic optimization in wirecut edm by using taguchi data envelopment analysis based ranking methodology”, International Journal Of Innovative Research Explorer, Volume 5 - Issue 3 - March 2018
  23. Dr.T.Prakash, “Low Cost Material Handling Equipment Using PLC”, International Journal Of Innovative Research Explorer, Volume 5 - Issue 3 - March 2018
  24. Dr.Subramanian.M, “Design and fabrication of organic fertilizer spraying machine”, International Journal Of Innovative Research Explorer, Volume 5 - Issue 3 - March 2018

 

 

 

 

Support